How Deep Will Gardener Denver 15w Go

11/30/2021

SMALL MUD ROTARY RIGS

FAILING 1500 (Ref#5063T)

Double drum drawworks, no mud pump (removed), 35' derrick, rotary table, mounted on International tandem axle carrier powered by Detroit 671 diesel engine, PTO drawworks/table driven, air throttle actuator, manual DW double plate friction clutches, slotted kelly, swivel, standpipe, mud line, valves, pressure gauge, kelly hose, rotary bushings, hydraulic breakout tongs, side walkways and railes, drill pipe slips, drill collar slips.
Single axle pipe trailer with walkways and approximately 550' of 2-7/8" pipe, (4) 4-1/2" drill collars, top hole collar, bottom hole collar for 7-7/8" bit, sub for 8-5/8" bit
16' box tandem axle tool/doghouse trailer
Repairs/Maintentance Required:
One bent A leg needs welding (driller side)
Two miltary tires on each side rear axle need to be replaced
Air filter and oil filer should be replaced, Aux Oil check, 3rd member should be greased.
Price: $33,500

GARDNER DENVER 1500 (Ref#8893T)

Completely refurbished 2018, GD2000 drawworks, air clutches, remote throttle, 5-1/2 x 8 Gardner Denver duplex mud pump, 35' kelly bar, port pit, LED package, new hyd valves, hoses cylinders. mounted on 2000 International 2674 triaxle chassis with 425 Cummins, 8LL transmission, 20,000front, 46,000 rear, 15,000 drop axle steerable, 7-1/2" rotary table with pulldown, 460' of 2-7/8" x 30' (2-3/8 IF) drill stem, 8-1/2" collar, 4-1/2" – 14" bitsPrice Reduced: $73,500

GARDNER DENVER 1500HD (Ref#4198RA)

Manufactured 1975, double drum, refurbished, air compressor (PTO), 5-1/2 x 8 mud pump, mounted on 1975 International with 6 cyl Detroit diesel engine, 38'9" derrick, 3 lines to hook, 3" swivel (reduced to 2" mud hose), 3-1/2" fluted kelly, 5 ½" stationary table, pipe rack, no pipe available Price: $87,500

GARDNER DENVER 1500 (Ref#2034R)

Manufactured 1971, 5-1/2 x 8" mud pump, no air compressor, 8" retractable table, kelly and kelly bushing, chain pulldown, driller's platform, pipe rack, mounted on tandem axle Autocar with Detroit 6V71 diesel engine, 4 hydraulic jacks, recently rebuilt Price: $99,500

GARDNER DENVER 1500 (Ref#1814Ta)

5 x 6 mud pump, stationary table, 4" kelly, mounted on 1979 International truck with diesel engine, PTO, pipe racks, 4 hyd leveling jacks, 200' drill pipe, needs new gearbox Price: $62,500

MAYHEW 1500 (Ref#15697T) Detroit 671 diesel deck engine, no mud, no air compressor, retractable table, 26' square Kelly (can run 33' casing), mounted on 1981 GMC Brigadier with Cat 3208 engine, pipe racks (holds approx. 500'), hydraulic breakout, hydraulic pulldown, air clutches, 3 leveling jacks, 900' drill pipe, 22' 3-axle trailer, (2) 4-1/2" x 20' drill collars, (1) 5-1/2" x 30' drill collar, misc change overs and pick up plugs Price: $54,500

MAYHEW 1500 (Ref#5015Ta) Gardner Denver 5 x 6 air driven mud pump, air compressor, 300 inline 6 cyl deck engine, double drum drawworks, 7-1/2" retractable table, mounted on tandem axle truck with Detroit diesel engine, 300' drill rod Price: $90,000

GARDNER DENVER 15W (Ref#2521T)

Manufactured 1974, complete rebuild, 5 x 8 high pressure mud pump, 54' derrick, 7-1/2" retractable rotary table (rebuilt 2018), Cummins 290 on deck, kelly bushing has been replaced, 290 Cummins deck engine, air clutches, wet clutch on main drive replaced, no air compressor, mounted on 4 axle Crane Carrier with 315 Cummins engine, 10 speed transmission, new clutch, tires 90%. Includes 340' of 4-1/2" x 20' drill pipe, 6" stabilizer, 5" stabilizer, new tires (90%), brakes, clutches and bearings have been replaced Price: $215,000

GARDNER DENVER 15W (Ref#8729N)

Manufactured 1974, Double drum drawworks with single brakes on each drum, Gardner Denver 700/250 air compressor with charger, 5-1/2 x 8 Gardner Denver mud pump, 4 cylinder injection pump, weight indicator, 55' x 2-1/2" round tubing derrick with racking board, mast, 3-1/2" x 35' square kelly bar, 4 line travelling block, 2" swivel, set up to run 31' joints of 3-1/2" or 2-7/8" drill pipe, 10" retractable table, 400 Cummins diesel engine, mounted on 4 axle Henrickson carrier, 3 leveling jacksPrice $200,000

GARDNER DENVER 15W (Ref#1053T)

Manufactured 1966, mounted on 4 axle crane carrier with 350 Cummins engine, standard mast, 5x8 mud (off rig, unmounted), WEK air compressor, 8" retractable table, 4 ½" x 23' fluted kelly, 15' rod box, new swivel, air clutches, hydraulic pulldown, 3 hydraulic leveling jacks, 700' of 3 ½" x 20' flush joint drill pipe, bits, subs, etc Price $55,000

GARDNER DENVER 15W (Ref#8645RB)

Manufactured 1978, PTO, mounted on CCC with diesel engine, (2) 5 x 8 mud pumps, 3 x 4 Mission mud pump, 10" retractable rotary table, 4" fluted Kelly, no air, 4 hydraulic leveling jacks, no pipe available Price Reduced: $165,000

GARDNER DENVER 15W (Ref#5509T)

Manufactured 1977, DSM drawworks, 5-1/2 x 8 mud pump, 10" table, WEJ air compressor, pulldown, mounted on 4 axle Crane Carrier, 400 Cummins engine, derrick extension with board, excellent tires, rod box, 300' of 20' (2-3/8 IF) drill pipePRICE REDUCED: $137,500

GARDNER DENVER 15W (Ref#10468T)

Manufactured 1977, Cummins 400 Big Cam 3 engine (less than 300 hours since in frame), 5-1/2 x 8 Gardner Denver mud pump, Gardner Denver WEJ 750/250 air compressor with blower, 52' x 100,000# 4-line derrick, 2500' racking board, hydraulic power tongs range 2-3/8 – 4-1/2, mounted on 4 axle Crane Carrier, 4 cylinder Bean mist pump, hydraulic hydramatic trip hold back, hydraulic kelly hold back, 4-1/2" square kelly with kelly cock, 10" Gardner Denver rotary table, swabbing drum with 2000' cable.
Drill pipe: 2000' of 2-7/8" x 20' (2-3/8 IF thread), 800' of 3-1/2" x 31' (3-1/2 IF thread)
Drill collars: 100' 3-3/4" x 20' (2-3/8 IF thread), 100' 4-1/2" x 20' (2-7/8 IF thread), 100' 6-1/4" x 20' (4-1/2 H90 thread)
Substructure: 5'H x 10'W x 44'L with retractable axle
Sullair 900 hp air compressor 350 psi (low hours)
5" x 10" Gaso skid mounted mud pump powered by 471 Detroit engine
5'H x 10'W x 42'L 300 bbl mud pit with hopper
5'H x 10'W x 42'L 330 bbl mud pit
7" Swaco rotating head
7" Hydrill BOP
35' tandem float pipe trailer with 4' x 8' parts house
1973 International water truck, 80 bbl with 355 Cummins engine
1968 Chevrolet 2-1/2 ton fuel truck with (4) 500 gal compartments
8' x 15' tandem crew trailer
2 pin Totco geolograph
Totco degree survey tool
Hydraulic survey machine with 8000' of high tensel steel line
8' x 40' shop made horizontyal drilling rig has drilled to 1800'
Tools, parts, X over subs, etc and more

PRICE RIG ONLY; $245,000

Package Price: ~~$650,000~~ REDUCED: $525,000

GARDNER DENVER 15W (Ref#748T) 5 x 8 mud pump, 54' mast, 8" retractable table, mounted on Crane Carrier, 400 Cummins engine, 1400' drill pipe
7 x 16 Gardner Denver mud pump (no engine)
Package Price: $225,000

GARDNER DENVER 15W (Ref#2217Ta)

No pump (1550 pump available at extra cost), 10" retractable table, 5-1/4" kelly, mounted on Carrier, Cummins engine, breakout wrench, pipe spinner, no rod box, no pipe rack, 4 hydraulic jacks, 1500' of 3-1/2" x 30' (2-7/8 IF) drill pipe (on tandem trailer) PRICE: $112,500
Also available: GASO 7 X 10 MUD PUMP (Ref#2217Tb) with Detroit 8V71 engine, on single axle trailer, only 200 hours Price: $50,000

GARDNER DENVER 15W (Ref#2585N)

Manufactured 1965, completely rebuilt and painted, mounted on 1997 International Paystar 5000 truck with Cat 3406 diesel engine (rebuilt), 5 ½ x 8 mud pump (rebuilt), WEJ air compressor, 10" GD retractable table, 58' mast, racking board, bailing drum, new 2" Little Giant swivel, new 26' kelly, hydraulic pulldown, air clutches, 3 hydraulic leveling jacks, 800' of 2-7/8" x 20' drill pipe, subs

~~Price~~ ~~: $270,000~~ PRICE REDUCED: $239,500

GARDNER DENVER 15W (Ref#15089R)

Manufactured 1978, 5-1/2 x 10 Gardner Denver mud pump, no air compressor, 10" retractable table, mounted on 1977 Autocar with 350 Cummins engine, PTO, air clutches, 58' extended mast, 4-1/2" x 24' kelly (smaller kelly available), piep rack, breakout tongs, racking boards, chain pulldown, 5 hyd levelng jacks

Price: $112,500

GARDNER DENVER 15W (Ref#5177N)

Manufactured 1980, mounted on 8 x 4 Hendrickson Crane Carrier, new 400 Cummins in 2004, 5-1/2 x 8 Gardner Denver mud pump, 50' mast, 650/250 WEJ air compressor with injection pump, 10" retractable table, new swivel, hydraulic pulldown, air clutches, bailing line, 4-1/2" x 24' fluted kelly, 4 hyd leveling jacks, 300' of 3-1/2" x 20' drill pipe, good condition, currently drilling

~~Price~~ ~~: $250,000~~ Pipe and tools available at extra cost.

PRICE REDUCED: $134,500

GARDNER DENVER 14W DRILL RIG (Ref#13060Ra) Manufactured 1973, 650/250 air compressor, Gardner Denver 5 x 6 mud pump, air clutches, 10" retractable table, mounted on Crane Carrier with 375 hp Cummins engine, 13 speed transmission, 3 leveling jacks, rod box, pipe racking stand, 210' of 4-1/2" x 15' drill pipe Price: $84,500
Available at extra cost:
1990 FORD L9000 WATER TRUCK (Ref#13060Rb) 1200 gallon tank mounted on bed, 350 diesel engine Price: $37,000

GARDNER DENVER 14W DRILL RIG (Ref#6234T)

Manufactured 1971, air clutches, 4-1/2" x 24' fluted kelly, pulldown, derrick board for 30' drill pipe (two 15' pipes connected), mounted on Crane Carrier, 350 Cummins 855 diesel engine, PTO, 10" rotary table, 600/250 GD air compressor, 5 x 6 GD mud pump, 600' of 4-1/2" x 15' drill pipe, good working condition Price: $79,500

Available at extra cost:
1990 Volvo White flat bed, 400 Cummins engine (rebuilt approx 2012 with low hours)
1979 Ford flatbed truck with Detroit 671 engine (needs rear tires)

GARDNER DENVER 1400 (Ref#15708T) Manufactured 1979, 5-1/2 x 8 mud pump, 256 SDS LeRoi air compressor, Bean injection pump, bailing drum, mounted on 1979 International Paystar 5000 truck, 290 Cummins engine, PTO, 4 levelng jacks Price: $137,500

GARDNER DENVER 1400 (Ref#1018T)

Mounted on 1982 Oshkosh 6WD truck, Cummins diesel engine, 7-1/2" retractable table, no air, Gardner Denver mud pump (an extra 5-1/2" x 8" Gardner Denver pump is available which was removed and replaced with smaller unit due to weight restrictions in the area), 300' drill pipe Price: $79,500

GARDNER DENVER 1400 (Ref#2084Ta)

5 x 8 Gardner Denver mud pump, 8-1/2" Midway rotary table (rebuilt), 44' new derrick, 2-1/2" Little Giant swivel, mounted on 1998 Freightliner truck with diesel engine, new 22' fluted kelly, friction clutches, rod rack, , Davey drop box, 135' of 4-1/2" x 2-7/8IF x 15' pipe, 45' of 4-1/2" x 2-7/8 IF x 15' collars, 20' of 4-1/2" x 2-7/8" OD Failing or 2-7/8" IF, runs 40' of casing joints, 3 hyd jacks Price: $105,000

GARDNER DENVER MUD ROTARY DRILL RIG (Ref# 7185T)

Built 1976, one owner rig, 5 x 6 Gardner Denver mud pump, 427 CFM piston air compressor, retractable rotary table
400' of 3" flush joint drill pipe (2-3/8 IF)
Drill collars
Spare GD427 air compressor
Approx 60 button and mill tooth drill bits (7-7/8, 8-1/2, 8-3/4 (new and rerun)
17-1/2" mill tooth tricone drill bit
8" drill bit
3 buckets of Baroid drilling mud
Misc parts, clutch plates, new drawworks jack shaft, new main bearing and race for rotary pot
Package Price: $140,000

GARDNER DENVER 1000HD (Ref#15652T) Manufactured 1979, 5 x 6 Failing mud pump, Leroi developmental air compressor, 23' fluted kelly, 7-1/2" retractable Speedstar table, hydraulic pulldown, air over hydraulic clutches, pipe rack, breakout wrench, mounted on International truck with DT466 engine, 3 hyd jacks, 300' of 20' pipe
Freightliner water truck with (2) plastics tanks, 2600 gallons total, diesel engine
Package Price: $70,000

MAYHEW 1000 (Ref#15087T)

Manufactured 1957, 5 x 6 Gardner Denver mud pump (new gear end and fluid end), 7-1/2" retractable table, 24' kelly, 35' mast, chain pulldown with hydraulic motor, mounted on 1973 Diamond Reo double frame, 290 Cummins engine, 8 speed transmission, engine and transmission new, 2 rear and 1 front leveling jacks, 320' of 2-3/8" drill pipe, ready to work Price: $52,500

MAYHEW 1000 (Ref#11322T) Mounted on 1994 Ford truck, Cat engine, 7-1/2" table, 5 x 6 Gardner Denver mud pump, 23' kelly, 2" swivel, hydraulic pulldown, water injection pump, 3 leveling jacks Price: $60,000

MAYHEW 1000 (Ref#8472T) Set up for drilling and workover, 4" square kelly, stationary table, mounted on 1974 International Lodestar, 5 x 6 Gardner Denver mud pump, no rod box, breakout tongs, 400' of 2-3/8" x 20' drill pipe, 10" surface bit, (2) 4" drill collars, 11 new button bits, 3 axle pipe trailerPrice: $44,500

MAYHEW 1000 (Ref#5448T)

Gardner Denver 5 x 6 mud pump, 5" rotary table, mounted on 1994 Hino truck, approx 300' drill pipe Price: $42,500

MAYHEW 1000 (Ref#6263T)

Manufactured 1980, Gardner Denver 5 x 6 mud pump, 600 cfm air compressor, 5-1/2" rotary table, 2" Little Giant swivel, mounted on 1980 Ford 9000 with rebuilt 6V71 Detroit engine, Eaton Fuller 10 speed transmission, 38' mast, chain pulldown, rod box, 8-1/2" fixed table, 2 rear jacks, 1 front jack, single rear end chasis, 400' of 2-3/8" drill rod Price: $47,500

MAYHEW 1000 (Ref#10423Ta)

Gardner Denver 667 air compressor, 5 x 6 Gardner Denver mud pump, Midway 1200 38' derrick and drawworks, mounted on 1979 International truck with 671 Detroit diesel with 500 hours, 250 pulldown chains Price: $59,500

GARDNER DENVER 1000 (Ref#13496T) Manufactured 1979, 5 x 6 mud pump, 200 cfm air compressor, 5-1/2" retractable table, 3-3/4" x 23' fluted kelly, hydraulic pulldown, mechanical clutches, pipe rack, pipe wrench, mounted on 1979 Ford 9000 truck with Detroit 6V92, 4 hyd jacks, drills daily Price: $94,500

MAYHEW 1000 (Ref#891Ta)

Manufactured 1978, 5 x 6 Gardner Denver mud pump, Gardner Denver air compressor, 5-1/4" stationary table, mounted on 1997 International truck with Cummins engine, 10 speed transmission, 30' mast, 25' kelly, chain pulldown, 2 rear leveling jacks, 300' of 2-7/8" IF drill pipe Price: $79,500

MAYHEW 1000 (Ref#891T) 5 x 6 Gardner Denver mud pump, IR air compressor, 7-1/2" Mayhew rotary table, 30' mast, 25' kelly, chain pulldown, air clutch, mounted on 1996 Ford LT9000 truck with Cummins engine, 2 rear jacks, 300' drill pipe Price: $89,500

MAYHEW 1000 (Ref#11597R)

Manufactured 1970, only 200 hours since in-frame overhaul, mounted on 1970 GMC with straight 671 Detroit engine, 5x6 GD mud pump, GD 580 air compressor, 18' kelly, hydraulic pulldown, mechanical clutches, breakout tongs, pipe rack, 1 front screw jack & 2 rear hydraulic leveling jacks, 150' of 2 7/8"IF x 15' drill pipe Price: $47,500

MAYHEW 1000 (Ref#3870R)

Air compressor, 5 x 6 mud pump, 23' kelly, 7-1/2" rotary table, mounted on 1996 International truck with Cummins 350 hp engine, 300' of 2-7/8" OD with 2-3/8 IF drill pipe, air clutches Price: $90,000

MAYHEW 1000 (Ref#5199R)

5 x 6 Garnder Denver mud pump, Gardner Denver air compressor, 5-1/4" stationary rotary table, mounted on 1997 Ford L9000 truck with Cummins 350 hp diesel engine, chain pulldown, 23' kelly, new brakes, new drums, new kelly bushings Price: $75,000

MAYHEW 1000 (Ref#11628R)

Mounted on single axle flatbed trailer,6 cyl Cummins engine, includes 2-ton Chevy with gas engine, 5x6 GD mud pump, dev air comp, 20' fluted Kelly, 5" stationary table, hydrostatic pulldown, mechanical clutches, breakout tongs, 20' drill collar, pipe rack, no leveling jacks, 200' of 2 3/8" x 20' drill pipe, sitting 1-2 years, but running when parked Price: $36,000

MAYHEW 1000 (Ref#10021N)

gardner denver

mounted on Rio 6x6 with Cat 3306 rebuilt engine, Fuller 10 speed transmission, Gardner Denver 5 x 6 mud pump, Leroi 100s air compressor, 2000 stationary table, 3 ½" x 23' Kelly, water injection pump, 500 gallon water tank, hydraulic pulldown, mechanical clutches, breakout wrench, 2 rear hydraulic leveling jacks, 200 of 2 7/8" x 20' drill pipe and International
Price: $55,000

MAYHEW 1000 (Ref#12694R)

Mounted on 1991 International truck with DT466 engine, 5 x 6 mud pump, 5-1/4" rotary table, hydraulic pulldown, 500' of 20' (2-3/8 IF) drill pipe, 2 hyd leveling jacks ready to goPRICE: $127,500

MAYHEW DSM 1000 DRILL RIG (Ref#5483T)

Completely refurbished 2010, derrick needs a little work, Mission Magnum Sandmaster 4 x 3 x 13 mud rotary pump, mounted on 1998 Mack CH613, completely with 2-3/8 pipe and various bits Price: $167,500

MAYHEW 1000 DRILLING RIG PACKAGE (Ref#8774T)

MAYHEW 1000 DRILLING RIG (Ref#8774T) 2007 Curtis 2-stage air compressor with intercooler, Wheatley 6 x 6 mud pump (rebuilt), 1000 Gardner Denver rotary (5 speed rotary transmission), 4 speed pulldown transmission, new pulldown winch, hydraulic flow control puldown, 1000 Mayhew drawworks (new brake drums), new 100 pulldown chains, all new sprockets on pulldown, newly rebuilt Little Giant swivel, 32' mast, new 23' kelly, mounted on 1977 International Fleetstar truck with diesel engine rebuilt in 2015 with about 1200 hours since rebuild, and back up camera, 2 hydraulic jacks, all components have been rebuilt in the last two years, 220' of 2-7/8" x 20' drill pipe (2-3/8 boxes and pins). Currently working
Price for rig and pipe: $65,000

MAYHEW 1000 (Ref#2362N)

PTO, mounted on 1971 White Constructor with 290 Cummins engine, 6 x 6 Wheatley mud pump, 580 CFM air compressor, custom made 42' mast, 36' Kelly, stationary table, mechanical clutches, pulldown, 1 front 2 rear hydraulic leveling jacks, no breakout wrench, no pipe or tools availablePrice: $42,500

MAYHEW 1000 COMBINATION RIG (Ref#1790Na)

Manufactured 1970, PTO, mounted on 1970 Chevy with gas engine, 5 x 6 Gardner Denver mud pump, 185 CFM on board air compressor with John Deere diesel engine, spudding arm, 5-1/4" stationary table, hydraulic pulldown, 3 hydraulic leveling jacks, 23' Kelly, 210' of 2 3/8" x 15' drill pipe, stabilizerPRICE REDUCED: $29,500

MAYHEW 500 MUD ROTARY DRILL RIG (Ref#4304T)

Mounted on 2007 International Workstar 7300 SFA 4 x 4 truck, mechanical clutches and cable drive, mud pump (rebuilt 2021), mud pan, International DT466E diesel engine (engine in-frame overhaul 6/21 with new international parts including cylinder head, hydraulic pump replaced 5/21, new batteries 6/21, 6 speed manual transmission, hi-low range with 2WD and 4WD, transfer case, 2 hydraulic jacks, air brakes, all tooling and accessories included: (14) 15' Mayhew Regular 15' rods, (1) 10' rod, (1) 5' rod, (3) coring bits, (3) wing bits, (1) diamond bit, (1) tricone bit, sand coring system with diamond bit, core barrel and tooling for barrel breakdown, air drilling system (air compressor not included) with (4) 15' Mayhew Jr 15' rods and (1) 10' rod. Ready to work. Price: $147,500

MAYHEW 500 (Ref#3374T)

5" stationary table, 4 x 5 Gardner Denver mud pump, developmental air compressor, 4" square kelly, hydraulic pulldown, mechanical clutches, mounted on 1990 GMC Kodiak truck with Cat 3208 engine, 3 hyd leveling jacks, pipe rack, 220' of 2-7/8" x 15' drill pipe Price: $49,500

MAYHEW 500 (Ref#9305R)

Manufactured 1984, 5 x 6 Gardner Denver mud pump (rebuilt Jan 2012), mechanical clutches, table drive, new kelly, swivel and subs, new cables, mounted on 1991 Ford L8000 truck with diesel engine, 300' drill pipe, subs, mud pan PRICE REDUCED: $26,500

GARDNER DENVER 500 (Ref#8865Ta)

Mounted on Ardco Model K 4 x 4 buggy, 4-1/2 x 5 Gardner Denver mud pump, 5" stationary table, pipe rack, chain pulldown Price: $59,500

MAYHEW 500 (Ref#7137T)

5 x 6 Gardner Denver mud pump, air compressor, 5-1/4" stationary table, no pulldown, 20' derrick, 900' of 2-3/8 x 10' drill pipe, ready to work Price: $64,500

MAYHEW 200 (Ref#10635R)

Manufactured 1974, mounted on Ford F600 truck, 390 engine, 3 levelng jacks, 600' of 2-3/8" x 10' drill pipe, no pulldown (can put back) Price: $13,000

GEFCO 135 (Ref#1254T)

Short wheel base, runs 15' pipe, 5-1/4 table, winch, 400/200 air compressor, 8 gpm water injection, mounted on Peterbilt 330 truck with Cat 3126E engine, RT8709B transmission, drill pipe, mud pit ~~Price:~~ ~~$140,000~~ PRICE REDUCED: $109,500

SPEEDSTAR 135 (Ref#3612T)

(2) 5 x 6 Gardner Denver mud pump, 7-1/2" rotary table, chain pulldown, 7 speed transmission, 466 engine (210 hp), 1991 International truck, 4 leveling jacks Price: $95,000

KOEHRING SS135 DRILL RIG (Ref#662T)

Built 1976, Wheatley mud pump, 5-1/4" retractable table, 2-7/8" x 24' fluted kelly, mechanical clutches, breakout tongs, mounted on 1981 International tandem axle truck with DT466 engine, 225' of 2-7/8" x 15' (2-3/8 IF) drill pipe, pipe racks, 3 jacks Price: $39,500

SPEEDSTAR SS-135-II (Ref#9683T)

Built 1979, 5 x 6 Gardner Denver mud pump, 100SDS air compressor, 15 gpm injection pump, sandline with new dable, 8-1/2" rotary table, 3-line blocks, new Little Giant swivel, kelly bar, kelly bushing, wear bushing in table, mud pump, 2 hydraulic pumps, clutches, new bearings, mounted on 1979 International 4900 truck with DT466 engine, Fuller 13 speed transmission, in frame rebuild on motor w/ some new cam injectors, includes extra mud pump and rig parts, 1200' of 2-7/8" (2-3/8 Mayhew Reg) pipe, tooling, ready to work Price: $93,500

SPEEDSTAR SS-135 DRILL RIG (Ref#11810Ta) Manufactured 1976, 5-1/2 x 8 mud pump, 8-1/2" DSM retractable table, mounted on 1994 Ford LN9000 truck with Cat 3306 engine, breakout wrench, rod box, 4 hyd leveling jacks, tools, 1000' of 20' 3-1/2" flush wall drill pipe, ready to work Price: $112,500

SPEEDSTAR SS-135 (Ref#3879TA)

290 cfm air compressor, John Deere deck engine for compressor, 8-1/2" retractable table, hydraulic pulldown, 5 x 6 Gardner Denvermud pump, mechanical clutches, mounted on tandem axle 1997 International 9400 truck with DT466 engine, approx 500' rods, some tools, good condition, ready to goPrice: $102,500

SPEEDSTAR SS-15-III (Ref#4921Tb) Manufactured 1983, 5-1/2 x 8 Gardner Denver mud pump, low pressure piston air compressor (compressor is 2 stage but only the low is working now), mounted on International 4700 with diesel engine, PTO, 11" retractable table, no rod box or pipe rack, some 3-1/2" x 20' bottleneck pipe included Price: $82,500

SPEEDSTAR SS-15 (Ref#2196T)

Manufactured 1971, 4-1/2" x 22' kelly, 8-1/2" retractable table, 256 LeRoi 525/250 air compressor, 3 drums, mounted on International truck with 8V71 Detroit engine, PTO, rod box, 300' of 4-1/2" x 15' drill pipe, 200' of 4-1/2" x 20' drill pipe, 15' drill collar with 6" hammer, stored inside, last drilled July 2021 Price: $83,500

SPEEDSTAR SS-15 III (Ref#11320TA)

standard mast & pullback, PTO, mounted on International with diesel engine, GD 5 ½ x 8 mud pump, Leroi air compressor, 500' of 4-1/2 x 20 flush joint drill pipePrice: $143,500

SPEEDSTAR SS-15 (Ref#14222Ta)

Gardner Denver 5 x 8 FXX172 mud pump, air compressor, 9" retractable table, 40' mast, pulldown, mounted on 1977 Crane Carrier, Cummins 855 diesel engine, 3 hyd leveling jacks, drill pipe Price: $115,000

SPEEDSTAR SS-15 (Ref#10125T)

Manufactured 1977, PTO, mounted on 1977 CCC with 290 Cummins engine, 3x4 centrifugal mud pump, Leroi 500/100 air compressor, 8-1/2" retractable table, 4-1/4" x 23' kelly, breakout wrench, pipe rack, 1 front & 2 rear hydraulic leveling jacks, 300' of 4-1/2" x 20' drill pipe, needs new truck Price: $39,500

CHALLENGER DRILLING RIG (Ref#4787T)

Manufactured 1979, mounted on International Paystar 5000 with 350 Big Cam Cummins engine, PTO, centrifugal mud pump, pipe rack, 3-1/2IF 20' drill pipe, currently drilling. Also includes unounted Gardner Denver 5-1/2 x 8 mud pump Price: $144,500

FAILING 1500 (Ref#3881NA)

Manufactured 1989, PTO, mounted on 1981 International with Cummins engine, 4x3 centrifugal mud pump, 900 CFM air compressor, hydraulic pulldown, mechanical clutches, 4-1/2" retractable table, 3-1/4" x 25' Kelly, chain pulldown, 3 hydraulic leveling jacks, rod box, portable mud pit, 200' of 3-1/2" IF x 15' drill pipe

~~Price~~ ~~: $145,000~~ PRICE REDUCED: $115,000

FAILING 1500 (Ref#11567T)

Manufactured 1980's, Gardner Denver 5 x 6 mud pump, chain pulldown, 4-1/2" kelly, 8-1/2" retractable table, Mounted on 1983 Peterbilt truck with Cummins 350 engine, PTO, 2 rear and 2 front levelng jacks, 800' of 2-7/8" drill pipe Price: $122,500

FAILING 1500 (Ref#13791R)

Manufactured 1970's, mounted on 1991 International with DT466 engine, 4 -1/2 x 5 Failing mud pump, auto chucks, 32' mast, 17' x 2 3/8" kelly, 2 leveling jacks Price: $49,500

FAILING 1500 (Ref#2827R)

1500 retractable table, 2-3/8" kelly, mechanical clutches, 5 x 6 Gardner Denver mud pumps, mounted on 1978 I6000 truck, Cat diesel engine, needs work (fluid ends needs rebuildeing, needs new hydraulic banks) Price: $49,000 PRICE REDUCED: $34,500

FAILING 1500 (Ref#4674N)

1500 drawworks, PTO, mounted on 1996 International 4700 4x2 truck with DT466 engine, (2) drilling pumps: Failing L100 800 max test pressure, 350 max working pressure and Gardner Denver FFFXFM 148.5 gpm, 639 max pressure, retractable table, mechanical clutches, hydraulic pulldown, 2 3/8" Kelly, 1 front & 2 rear hydraulic leveling jacks Price: $38,500

FAILING 1500 (Ref#7758T) 8" retractable table, Ford gas deck engine, mounted on 10 wheeler with gas engine, 3 hyd leveling jacks, no rod box or pipe rack, incluees 390' of FEDP pipe, 14" bit Price: $19,500

FAILING 1500 DMX (Ref#11680T)

Manufactured 1970's, trailer mounted, Cummins engine, 5 x 6 Gardner Denver mud pump, 18" rotary table, no compressor, no drill pipe Price on Request

FAILING 1500 HOLEMASTER (Ref#8617R)

Manufactured 1964, 5 x 6 mud pump, 2-3/8" kelly bar, 20" table (opens to 22"), heavy duty mast, 2 winches w/15" clutch, hydraulic pulldown, mounted on 1964 International truck, PTO, double plated frame, 304 International engine, needs minor repairs
1000' 2-3/8" x 20' drill pipe with Acme threads (3 TPI)
1979 Ford FL7000 water truck, flat bed, 1800 gal water tank, Cat 3208 engine
Package Price: $62,500

FAILING 250 (Ref#8037Ra)

Mounted on 1986 Ford F600 4 x 4 truck with Detroit diesel engine, PTO, 4-1/2 x 5 mud pump, chain pulldown, 5" retractable table, 2-7/8" kelly, runs 10' drill pipe, includes 100' drill pipe and misc bitsPrice: $48,500

FAILING CF15 (Ref#557Ta)

Two available, 2006, Gardner Denver 5-1/2 x 8 mud pump, 39' x 45,000# tubular steel mast, low hours, located Texas Price: $165,000

FAILING CF15 DRILL RIG (Ref#4536T)

Manufactured 1988, no mud pump, no air compressor, 6-1/2" inner diameter / 11" outdoor diameter retractable rotary table, 3-1/2" x 21' kelly, mechanical chain pulldown, mechanical clutches, rod box, sandline, mounted on 1988 International FSeries 6 x 4 truck with DT466 gas engine, Eaton 10 speed tranmission, 200' of 2-3/8" drill rod, truck and rig is operatable but could use some work, 3 leveling jacksPrice: $41,500

FAILING CF15 (Ref#2569N)

Manufactured 1979, 5 x 6 Gardner Denver mud pump, Leroi 50S2 air compressor for drilling, 8" retractable table, 3-3/8" x 23'6"' kelly, 31'6" heavy duty mast, pulldown, mechanical clutches, Myers water injection, mounted on GMC Brigadier truck with 3208 Cat engine, 3 hydraulic leveling jacks, 500' , 3-5/8 x 15' drill pipe, bits, subs, good condition

~~Price~~ ~~: $95,000~~ PRICE REDUCED: $75,000

FAILING CF-15 DRILL RIG (Ref#4735T)

Manufactured 1979, SDS 50 air compressor, 4 x 3 centrifugal mud pump, mounted on 2000 Volvo truck with diesel engine, 7-1/2" retractable table, air clutches, rod rack, completely tooled, 360' OF Failing 2-3/8 x 20' drill pipe, freshly painted Price: $162,500

FAILING CF15 (Ref#8369N)

Manufactured 1974, LeRoi 50S2 air compressor, 5 x 6 mud pump, 5-1/4" retractable table, 3-3/8" fluted kelly, 3 hydraulic leveling jacks, pulldown, mechanical clutches, breakout wrench, mounted on 1974 International tandem axle truck with Detroit 8V71 diesel engine (overhauled less than 1000 hours), 200' of 2-7/8" x 20' drill pipe

Price: $77,500

FAILING CF-15 (Ref#10629T)

Manufactured 1969, 5 x 6-1/2 mud pump, 8" retractable table, chain pulldown, 20' kelly, 23' mast, sandline, mounted on 1969 Chevrolet 3-axle truck with Detroit engine, 3 leveling jacks, 400' drill pipe Price: $64,500 PRICE REDUCED: $55,000

FAILING CF-15 (Ref#14101T)

Manufactured 1978, Gardner Denver 7-1/2 x 10" mud pump, 8" DSM retractable table, mechanical clutches, no pulldown, 35' fluted kelly, plumbed for breakout, 3" plumbing, mounted on 1978 Ford 9000 tandem axle truck with 300 Cummins, air brakes, ready to drill Price rig only: $79,500

Available at extra cost:
1000' of 4" x 20' (2-7/8" IF) aluminum flush joint drill pipe on 2 axle trailer with laydown system
Package Price: $123,500

FAILING 1250 DRILL RIG (Ref#12048T)

Mounted on 1995 International 4900 truck, DT 466 engine, 500,000 miles, Eaton Fuller RT-6613 transmission, 10 speed, 315' drill pipe, working condition Price: $73,500

FAILING 1250 (Ref#14720Ta)

Mounted on 2000 Freightliner truck, 3126 Cat engine, 5 x 6-1/4" Failing mud pump, developmental air, 5-1/4" retractable table (also has a 7-1/2" available), chain pulldown, PTO, ready to workPrice: $162,500

FAILING 1250 (Ref#6070Ra)

Manufactured 1988, PTO, mounted on 1993 Ford 9000 with 250 Cummins engine, 9 speed Fuller transmission, 5 x 6 mud pump, no air, 5-1/4" stationary table, 2" Little Giant swivel, 18' x 3 5/8" round Kelly, hydraulic pulldown, mechanical clutches, breakout tongs, 2 rear hydraulic leveling jacks, 200' drill pipe, ready to go

~~Price~~ ~~: $70,000~~ PRICE REDUCED: $55,000

Mayhew Reg Pipe available at extra cost

FAILING 1250 (Ref#10385Na)

Manufactured 1972, 5 x 6 mud pump, 50S1 LeRoi air compressor, pulldown, mechanical clutches, mounted on International tandem axle truck with gas engine, 40,000# mast, 15,000# drawworks, 3 drum bailer, single line pull, driller and helper's platforms, hydraulic pulldown with 1-1/2" pulldown chains, 2" Little Giant swivel, toolracks, 3 hydraulic leveling jacks, 240' of 3-1/2" x 15' FJ (2-3/8 IF) drill pipe, LF breakout wrench, good condition, currently drilling ~~Price~~ ~~: $90,000~~ PRICE REDUCED: $87,500

FAILING 1250 DRILL RIG (Ref#245N)

Manufactured 1980's, mounted on 1991 GMC tandem axle truck with a title. Powered by Detroit 300 HP diesel engine and PTO. 5x6 Gardner Denver hydraulically powered mud pump with 500 / 200 air compressor. 3 7/8" x 23' fluted Kelly. Pulldowns, air clutches, Bean water injection, hammer oiler. 5-1/2" retractable rotary table, breakout tongs, 4 hydraulic leveling jacks. 250' of 2 7/8" x 20' drill pipe. Rod box. Driller's platform, helper's platform. Not been used in several years but does start up. Price Reduced: $42,500

FAILING 1250 (Ref#3873R)

Manufactured 1980, mounted on 1980 International truck with DT466 engine, 5 x 6 Gardner Denver mud pump, no air compressor, 5-1/4" retractable rotary table, 3-1/2 X 24' kelly, chain pulldown, 2" swivel, new fuel pump, new head gasket Price: $57,500 PRICE REDUCED: $48,500

FAILING 1250 (Ref#4642R)

Manufactured 1970, completely rebuilt, 5 x 6 Failing mud pump, developmental air compressor, sandline, mounted on 1990 Freightliner truck with Cat 3406 (600 hours), 5-1/4" retractable table, rod box, mechanical clutches, chain pulldown, 2" rebuilt swivel, new 32' mast, well maintained, ready to drill, no drill pipe

~~Price~~ ~~: $80,000~~ Price Reduced: $64,500

FAILING 1250 (Ref#12693T) Manufactured 1973, 5 x 6 mud pump, chain pulldown, retractable table, mounted on 1973 International truck, 345 gas engine, no drill pipe Price: $54,500

FAILING 1250 (Ref#14820T) Manufactured 1965, mounted on 1970 Chevy with gas engine, 5x6 mud pump, 5-1/4" retractable table, 18' kelly, hydraulic pulldown, mechanical clutches, breakout wrench, 1 front & 2 rear hydraulic leveling jacks, hydraulic pump has been removed, stored inside, sitting but running when parked Price: $30,000

FAILING 1250 (Ref#14641R)

Parts rig, not running, manufactured late '70's, PTO, mounted on '85 GMC with V8 gas engine, 5 x 6 mud pump, no air, 5-1/4" retractable table, 2 3/8" x 23' Kelly, breakout wrench, hydraulic pulldown, mechanical clutches, 3 hydraulic leveling jacks, sitting a while but running when parked Price: $17,500
400' of 2 3/8" x 20' drill pipe available

FAILING CFD2 DRILL RIG (Ref#8107T)

Built 1964, 4-1/2 x 5 Failing mud pump, Grimmer Schmidt 125cfm developmental air compressor, 5-1/4" stationary table, 2-3/8" kelly, mounted on 1984 International truck with DT466 engine, PTO), 4 hydraulic over mechanical jacks
340' of May Jr Rods
340' N rods
1987 International water truck, 1500 gallon tank, diesel engine, underbody toolboxes
1997 International water truck, approx 1000 gallon tank, DT466E engine, underbody toolboxes
Has not run in since 2016
Package Price: $62,500

FAILING CFD-1B (Ref#14819T)

Manufactured 1965, mounted on 1979 International S series 2551 tandem axle truck with DT466 diesel engine, (2) mud pumps: Failing FM45 5 x 6 duplex and Gardner Denver FG FXG 5 x 6 duplex, Ingersoll Rand Type 30 250/125 air compressor hydraulically driven, 26' x 25,000# derrick, 3-3/8" x 18' kelly, King 15 KF water swivel, 1-1/4" pulldown chains, 5-1/4" rotary table with locking nut, air controlled clutches, welder, pipe rack, 150 gal mud pit, breakout tongs, 1 front & 2 rear hydraulic leveling jacks, stored inside, sitting but running when parkedPrice:$27,500

FAILING CFD-1B (Ref#4323T)

Mounted on 1980 International S1954 single axle truck with DT466 engine, 26' x 26,000# derrick, 5-1/4" rotary table with locking nut, 3-3/8" x 18' fluted kelly, Failing S1200 water swivel, 1-1/4" pulldown chains, Failing FM45 5 x 6-1/4 duplex mud pump, Ingersoll Rand Type 30 250/125 air compressor, bailing drum, 4 speed transmission, manual clutches, welder, pipe rack, mud pit Price: $22,500

FAILING CFD-1B (Ref#3990)

Manufactured 1973, 6 x 4-1/2 Gardner Denver piston mud pump (rebuilt), 5-1/4" fixed table (rebuilt with new bearings and seals), new cables on drawworks, new clutches and bearings on 3 speed Spicer transmission on deck, hydraulic chains, well maintained, Mounted on 1973 Ford F600 single axle with 391 Cleveland gasoline engine, 3 leveling jacks, PTO, 200' of 2-3/8" drill pipe, completely tooled with bits, mud pan PRICE: $22,500

FAILING CFD-1 (Ref#1957N)

5 x 6 Wheatley mud pump, Gardner Denver developmental air, hydraulic pulldown, mechanical clutches, stabilizer, mud pan, 3-1/2" kelly, stationary table, mounted on Ford Louisville tandem axle truck with 290 Cummins engine, PTO, 2 rear hydraulic jacks, 200' of 3-1/2" x 20' drill pipe, good condition, currently drilling ~~Price~~ ~~: $65,000~~ PRICE REDUCED: $50,000

FAILING 1000 (Ref#319N)

3 x 4 Gardner Denver mud pump, 650/50 compressor, PTO, mounted on 1979 International 2-ton tandem axle truck with diesel engine, 3-1/2" kelly, 7-1/2" fixed table, 3 hydraulic jacks, pipe rack, mechanical pulldown, 300' of 2-7/8" drill pipe (2-3/8 IF) PRICE:$52,500

FAILING HOLEMASTER 1000 (Ref#2616T)

Mounted on 1974 Mack truck with V8 Mack engine, new 2" Little Giant swivel, 23' kelly, 5-1/4" rotary table, 256 LeRoi air compressor, 5 x 6 Gardner Denver piston pump, 2 hyd jacks, low hours, ready to work PRICE REDUCED: $72,500

FAILING CFD-2 (Ref#3011R)

Mounted on 1996 Ford F series 2 wheel drive with 5.9 Cummins diesel engine, 5-1/4" stationary table, 2 3/8" x 15' Kelly, 5x6 GD mud pump, chain pulldown, mechanical clutches, breakout wrench, rod rack, 255' of 15' Mayhew Jr rods, subs, bits, casing elevators, 4 hydraulic leveling jacks, ready to go

PRICE REDUCED: $52,500

FAILING 750 HOLEMASTER (Ref#894T)

4-1/2 x 6 Gardner Denver piston mud pump, no air, 2-7/8" x 18' kelly (runs 10' x 2-708" rods), mounted on 2000 International 4700 w/DT466 engine, no drill rod, Mayhew Junior thread on kelly, all new hydraulic control valves, brakes clutches are all new or have recently been replaced Price: $37,500

FAILING 250 (Ref#3448T) Manufactured early 1970's, mounted on Ford 6 wheel drive Ford F750 truck, 391 gas engine, 4-1/2 x 5 mud pump, 290 cfm air compressor, 4" retractable table (no casing can go through), chain pulldown, 2-3/8 kelly, sandline, 10' stroke (can be pulled to 20'), running condition Price: $29,500

MIDWAY 15M (Ref#3049T)

5-1/2 x 10" duplex mud pump, 256S2 LeRoi compressor, 50' derrick, monkey board, chain pulldown, air clutches, 8-1/2" retractable table, mounted on 1998 Mack tandem front, tandem rear truck with Mack diesel engine, no pipePrice: $139,500

MIDWAY 15M DRILL RIG (Ref#6505T)

Mounted on 1991 Kenworth truck, 54' mast, 5-1/2" x 8" mud pump, 500/250 air compressor, 8-1/2" retractable table, spinning chains, 4 hyd jacks, 2-1/2" Little Giant swivel
1981 Kenworth Water Truck, 4500 gal stanless steel tank, 3 axle
Package Price: $370,000
1500' of 4-1/2" x 2-7/8 IF drill pipe

MIDWAY 15M (Ref#7588R)

Manufactured 1980, Midway 1500 drawworks, PTO, mounted on 1980 International f-2574 with 1996 Detroit engine, 10 sp transmission, 38000# rear axles, 24.5 bud wheels, 16000# front axle w/22.5 floatation tires, 4 leveling jacks, 5 ½ x 8 mud pump, new 8-1/2" Midway retractable table, 3-3/4" x 34' fluted kelly (new 2011), 3-3/4" x 5-1/4" new master bushing, 49'2" mast with new cylinders (can run 44'5" casing), 3" plumbing, 2" swivel, 2" kelly hose, hydraulic pulldown, new drivemotor 2013, hydraulic cathead, 792 Spicer transfer case (rebuilt 2013 with air controls), new lifting cylindes on mast, new main hyd pump 2012, 4 part linesm BVM breakout tong, heavy duty work floor with hinged trap door

1600' of Range II pipe (2-7/8 IF) with trailer, doghouse, drill collars, 1991 International winch truck, 1995 International bus doghouse, tools, subs, welder, torch and spare parts
Package Price: $258,500

MIDWAY 15M (Ref#9252Ra)

Manufactured 1975, drawworks completely rebuilt, 7-1/2 x 10 Gardner Denver mud pump, hydraulic pulldown, 54' derrick with racking board, rod box, mounted on 1978 International Paystar 5000 truck with 350 Cummins engine. Price: $139,500

MIDWAY 1500HD (Ref#5232T)

5-1/2 x 10 Gardner Denver mud pump, no air, hydraulic chain pulldown, 12-1/4" retractable table, 54' derrick, mounted on Ford tandem axle truck with Cat 3406, PTO, laydown trailer with 900' of drill pipe Price: $139,500

MIDWAY 1500 (Ref#5033T) 5-1/2 x 8 mud pump, 256 SDS air compressor, Bean water injection pump, mounted on 1977 Autocar truck with 290 Cummins engine, PTO, 4 leveling jacks Price: $97,500

MIDWAY 1500 (Ref#15626R) Manufactured late 1970's, no mud pump, square kelly, no pulldown, 8" retractable table, mounted on newer Freightliner truck with diesel engine, air clutches, no pulldown, breakout tongs, 1 front and 2 rear hydraulic leveling jacks, no rod box, no pipe rack, 300' of 20' drill pipe (2-3/8" IF), Price: $54,500

MIDWAY 13M (Ref#6704R)

Manufactured 1977, 600 cfm Leroi air compressor, 5 x 6 Gardner Denver mud pump, 8-1/2" table retractable, pull down, 9 gpm Bean pump, mounted on 1977 Ford 9000 truck with 671 Detroit engine (overhauled 2014), 600' of 2-7/8" drill stem, well maintained, ready to work ~~Price~~ ~~: $162,500~~ PRICE REDUCED: $105,000

MIDWAY 13M (Ref#14795T)

Manufactured 1978, PTO, mounted on 1979 Ford 9000 with Cat engine, 5x6 mud pump, Leroi 750cfm air compressor, 3" x 23' kelly, 8" stationary table, breakout wrench, rod box, hydraulic pulldown, mechanical clutches, mud pan, 300' of 2 7/8" x 20' drill pipe, no leveling jacks, good running condition

~~Price~~ ~~: $80,000~~ PRICE REDUCED: $54,500

MIDWAY 1250 (Ref#12353R)

PTO, mounted on 1991 Mack with diesel engine, 5x6 mud pump, GD air compressor, 7-1/2" stationary table, pulldown, manual clutches, rod rack, 2 hydraulic leveling jacks, good conditionPrice: $67,500

MIDWAY 500 (Ref#7956Tb)

Manufactured 1969, LeRoi 100 S1 air compressor, Gardner Denver 5 x 6 mud pump, 30' mast, mounted on 1969 Peterbilt truck, new rear jacks, rebuilt transfer case, 200' of 2-7/8" drill pipe, parts Price: $84,500

FRANKS 55 (Ref#1849N)

franks drill rig

32' square kelly, 51' mast for Range III casing, mounted on GMC truck, propane engine on deck and in carrier, 8" retractable table, air clutches, approx 800' of 2-7/8 IF Range 2 drillpipe and collar on trailer, 5 x 8 Gardner Denver mud pump with Cat diesel power on trailer, GMC single axle gas truck tractor, ready to drill

~~Price~~ ~~: $100,000~~ PRICE REDUCED: $95,000

FRANKS KF50 (Ref#10744T)

3 drum drawworks, mechanical clutches, Spicer air shift PTO, 2 rear hyd leveling jacks, 8" retractable table, 3-1/2" x 24' square kelly, 2" Little Giant swivel, new 3 x 4 Mission mud pump, hydraulic pulldown, mounted on 1993 Freightliner truck with Cat 3406 engine, approximately 400' of 2-7/8" full hole drill pipePrice: $62,500

PORTADRILL 10TG (Ref#15047RB)

Manufactured 1969, 318 Detroit deck engine, mounted on 1986 International Paystar 5000 with 300 Cummins engine, 5x6 GD mud pump, Leroi 256 S2 air compressor, 10" retractable rotary table, 37' mast, cable drawworks, 9 gpm Bean water injection, brand new Kelly bar, hydrofracture machine, mud pit, 360' of 4 ½" drill pipe ( 2 7/8IF) PRICE : $40,000

PORTADRILL 524 (Ref#757N)

Manufactured 1979, fully overhauled, PTO, mounted on 1996 Kenworth with Cummins engine, 5-1/2 x 8 mud pump, Leroi 256S2 air compressor, 7-1/2" retractable rotary table, 4-1/2" x 24' kelly, 50' mast, 4 hydraulic leveling jacks, 300' drill pipe

PRICE: $125,000

PORTADRILL 524 (Ref#2592R)

portadrill 524

Manufactured 1979, mounted on 1979 International Paystar 5000 truck, 5 leveling jacks, 7-1/2" retractable rotary table, 26' kelly, 2" Little Giant swivel, 5-1/2 x 8" Gardner Denver mud pump, 256 LeRoi air compressor, racking board, currently working PRICE REDUCED: $92,500

PORTADRILL 521 (Ref#1646N)

5-1/4" retractable table, 24' kelly, 5 x 6 Gardner Denver mud pump, 30,000# pulldown, mounted on 1988 International truck 365 hp engine, PTO, 1 front 2 rear hydraulic leveling jacks, 350' drill pipe 2-7/8 FEDP, good condition Price: $89,500

PORTADRILL 120 (Ref#9801T) Manufactured 1968, 5 x 6 Gardner Denver mud pump, 6" stationary table, 3-1/2" x 23' kelly, mounted on 1987 Peterbilt with diesel engine, PTO, pipe rack
1989 Kenworth Water Truck, diesel engine, 9 sp transmission, 2500 gallon plastic tank
Dual axle trailer with Ford backhoe
Wheatley 6 x 6 mud pump (no engine)
Many spares
200' of 2-3/8" x 20' pipe
Package Price: $95,000

INGERSOLL RAND RO-300 DRILL RIGS (Ref#1555Ta) Detroit V8 engine, 11 speed transmission, 5 x 10 Gaso hydraulic mud pump, 42' mast, 8-1/2" retractable table, 4-1/2" x 25' fluted round kelly, hydraulic drive winch, mounted on 1980 International, 4 hyd jacks Price: $137,500

INGERSOLL RAND RO-300 DRILL RIG (Ref#1555Tb) Detroit V8 engine, 11 speed transmission, (2) 5 x 6 Gardner Denver hydraulic driven pumps, 8-1/2" retractable table, 42' mast, hyd driven double drum winch, w/ram driven kelly, 5-1/2" x 25' kelly, mounted on 1981 International Paystar truck, 4 hyd jacks Price: $137,500

INGERSOLL RAND RO-300 (Ref#4472T) Early 1980's rig, PTO, mounted on International tandem axle truck with Detroit 8V92 engine, 8" retractable table, 4-1/4" x 24' fluted kelly, hydrauluic pulldown, 25,000# main winch, 3000# sandline, rod box, 32' mast, 3 hyd leveling jacks Price: $56,500
Available at extra cost:
(Ref#4472Tb) 560' of 4-1/2" x 20' drill pipe (3-1/2" IF) complete with bits, subs, etc. POR

DAVEY M-8 (Ref#2804Na) Manufactured 1978, mounted on 2012 Mack Granite truck with Mack diesel engine (9000 miles), 6V71 Detroit diesel deck engine (rebuilt 2007), 550/150 air compressor (rebuilt 2006), 4-1/2" x 30' kelly, dust collector, 300' of 4" x 20' drill pipe, good conditionPrice: $94,500

DAVEY M8A (Ref#6251T)

Manufactured 1977, 500/125 air compressor, Detroit 6V71 deck engine, 8 gpm Myers injection, pump, 32'4" kelly, 7-3/8" stationary table, mounted on Ford 9000 truck with Cummins L10 engine, Eaton 8LL transmission, 210' of 4" X 10' drill pipe, stored inside, working condition Price: $33,500
Parts available at extra cost

DAVEY M8W KELLY AIR RIG (Ref#2884Na)

Manufactured 1976, mounted on Louisville Ford truck with 54 gas Ford engine, 5 and 4 transmission, new clutch, 38,000# rear, 26-1/2' Kelly bar 4" round, King swivel, 35' tower, 7-1/2" sliding table, 671 Detroit diesel deck engine, 500 cfm/125 psi Davey air compressor rebuilt with less than 2000 hours, water injection system hydraulically operated, 100' of 4" x 20' flush wall drill pipe, can drill to 900', can hold 300' steel

PRICE: $35,000

DAVEY M8A (Ref#4490T)

Manufactured 1975, low hours on Detroit 6V71 inline C series deck engine (500 hours as of October 2018), new 5/8" non-rotating line on drawworks, 2 speed gear box to slow down drawworks, new pulldown, new hydraulic pump (400 hrs), new flotation tires in front, 500/125 air compressor, rod box, 7-1/2" stationary table, 34`" x 4-1/2" kelly, new bushings in kelly block, 40' long derrick, mechanical clutches, dual line on pipe pickup, 300 gal water tank mounted on front of rig, mounted on 1989 Ford LT900 truck with 425 hp Cat 3406B engine, 18 speed Eaton transmission with overdrive, 48,000 lb Rockwell rear ends, 425x22.5 tires, 3 leveling jacks, front bumper extended, dual 100 gal fuel tanks, 300' of 3-1/2" x 20' pipe, small subs and bits Price: $69,500

DAVEY M8 KELLY AIR RIG (Ref#2884Nd)

Manufactured 1975, mounted on tandem axle Ford Louiville truck with 534 gas engine, 5 x 4 transmission, leveling jacks, 38,000# rear, good tires, 671 Detroit diesel engine, 500 cfm/125 psi Davey air compressor, rod box, holds 300' drill pipe, 100' of 4" x 20' drill pipe, slips, 7-1/2" fixed table, 32-1/2' x 4-1/2" Kelly bar, runs 4" drill string, 46' one piece mast (can be reduced), work platform

~~Price~~ ~~: $40,000~~PRICE REDUCED: $27,000

DAVEY M8 (Ref#8066Ra)

Rebuilt 671 Detroit diesel engine on deck, 400 cfm air compressor, new 25' kelly, 7-1/2" retractale table, mounted on 1975 International truck with gas engine (tank has rust in it and needs cleaning), 3 hyd leveling jacks, 320' of 3-1/2" x 20' drill pipe, 1 bit, 1 sub PRICE REDUCED: $25,000

DAVEY (Ref#10682T)

500/125 Davey air compressor, 7-1/2" fixed table, 32-1/2 x 4-1/2" kelly bar, 46' one piece mast (can be reduced), 671 Detroit deck engine with 5 x 4 transmission, mounted on 1978 Ford 900 tandem axle truck with 534 gas engine, leveling jacks, 38,000# rear, rod box (holds 300' of pipe), slips, work platform, 200' of 2-7/8" drill pipe, runs 4" drill pipe

PRICE REDUCED: $49,500

SHOP BUILT MUD ROTARY DRILLING RIG (Ref#7785T)

Built approx 2007, 150' – 200' depth capacity, rig has heavy duty railroad winch cable for up and down drilling operations or for pulling pumps, 3" centrifugal mud pump, IR 40 cfm developmental air compressor, pump and compressor run off Handona gas engines, boom will handle 10' or 20' rods, mounted on 1998 Ford 700 2 wheel drive truck, 7 ltr propane engine, (2) tanks (40 and 80 gal), drilling, hydraulics and truck run on propane, 500 gal water tank, pipe rack, compact rig. Includes approx 120' of 1-1/4" x 10' rods, bits for 1-1/4", 2" and 4" wells, Price: $34,500

BUCYRUS ERIE 10R (Ref#5558Ta)

Manufactured 1974, mounted on 1974 Ford LN8000 with rebuilt Cat 3208, new front tires, no ruse, LeRoi compressor, 5 x 6 Gardner Denver mud pump, injection pump, new 2" plumbing, 8" retractable table, 3 hyd jacks, rod rack, 5 stabilizers 6"-12", 19 rods of 2-7/8", 26 rods of 3-1/2", several bits and subs 4"-10"

2005 FREIGHTLINER WATER TRUCK (Ref#5558Tb)

1000 gal water tank, C7 engine, tandem axle, 18,000# boom with 60' reach, 250 Miller welder and generator, grouter, 18' rack, toolboxes, air brake trailer package, hitch

Package Price: $114,500 CDN

BUCYRUS ERIE 10R (Ref#11705T)

Manufactured 1973, 5 x 6 Gardner Denver mud pump (new pistons and liners 2016), 50 SDS air compressor, bailing drum, 24' kelly, 8-1/4" retractable table, hydraulic pulldown, air clutches, mounted on 1989 Chevy Topkick with Cat 3208T, rod box, 300' of 3" drill stem, tools, well maintainedPrice: $47,500 Additional pipe available at extra cost.

BUCYRUS ERIE 10R (Ref#8962R)

Manufactured 1970, 38' mast, 5 x 6 Gardner Denver mud pump, 50 SDS air compressor, 2 line, 8-1/4" retractable rotary table, water injection, mounted on 1968 White 9000 with 250 Cummins engine, 13 speed transmission, 225' of 3-1/2" with 2-3/8 IF pipe Price: $69,500

Available at extra cost:

1996 INTERNATIONAL 4700 WATER TRUCK (Ref#8962Rb) 1400 gal water tank, 18,200 miles, good rubber, DT466, 6 speed Price: $34,500

BUCYRUS ERIE 10R (Ref#7956Tc)

Manufactured 1972, no air compressor, no mud pump, 34' mast, mounted on 1971 White truck with Cummins diesel engine Price: $30,000

BUCYRUS ERIE 10R (Ref#11695Tb)

5x6 Gardner Denver mud pump (rebuilt), developmental air compressor, table drive with 7-1/2" retractable table, 20' kelly, mounted on Ford 9000 tandem axle truck with Cummins PTO diesel engine (engine needs to be replaced), drill rigis in good running condition Price $29,500

EWBANKS 50 (Ref#13911Ra) 4 x 5 mud pump, mounted on 1978 International single axle truck, Cat 3208 engine, PTO, 5-1/4" stationary rotary table, no air, square kelly, mud pan, pipe rack, 200' pipe Price: $37,500

MOBILE B40-L12 (Ref#5066T)

Built 1986, mounted on 1986 GMC Brigadier truck with Cat 3208 engine, Ford 4 cylinder Industrial deck engine, 5 x 6 mud pump, 1 mainline winch, 1 sandline winch with free fall, sitting outside for a while, was in proper working condition when parked Price on Request

CYCLONE F50 DRILLING RIG (Ref#5426T)

Mud rotary rig, mounted on single axle International 4700 4 x 4 truck with DT466, 200' Mayhew Jr rod Price: $50,000

SANDERSON CYCLONE 36R COMBINATION ROTARY/SPUDDER RIG (Ref#11403Tb)

4 cylinder Ford diesel engine on deck, 38' hydraulically raised mast, 5-1/2" table retractable to 18" x 12" deep, 3-1/2" x 20' fluted Kelly, drill line drum, sandline drum and casing drum (no line on rig). 2-part block, shock in the crown for cable drilling, Mounted on 1992 Ford L7000 all-wheel drive truck with 6 cyl Ford diesel engine, automatic transmission with big hydraulic pump, low miles, 3 hydraulic leveling jacks, needs new hoses and swivel. Price: $32,500 - Oklahoma

CYCLONE 35R (Ref#6558T) 5" Gardner Denver mud pump with 3 cyl diesel engine, no air, square kelly, retractable table, hydraulic pulldown, pipe rack, 4 cylinder diesel deck engine, mounted on 1985 Mack twin screw with diesel engine, 3 hyd leveling jacks, 300' of 2" x 16' drill pipe Price: $64,500

CYCLONE 35R COMBINATION MUD ROTARY CABLE TOOL RIG (Ref#10514T)

Built 1966, 5 x 6 mud pump, developmental air compressor, mounted on 1966 Ford F950 Super Duty with gas engine, (2) gas deck engines (one runs rig, one runs air compressor and mud pump), 240' drill rod, 15' sub and bit Price: $29,500

PIPER HYDRO HYDRAULIC RIG (Ref#10305Tb)

Built 1980's, trailer mounted, new swivel, 420cc engine, 250' – 500' depth, 30 gpm hydraulic pump (newer hoses), 2000# electric winch, 2" mud pump, 2 gpm mist pump, 250' of drill pipe, 2 drill collars, tooling, bit, subs,. 180 cfm Sullair compressor, water tank/pipe trailer Price: $46,500

SUN 500' DRILL RIG – NEW MANUFACTURE (Ref#12607T)

Built new 74 HP Kohler Tier 4 Turbo diesel industrial deck engine, Industrial Permco dual 28 gpm main pump w/vari speed split driver circuits in volve controls, 3 x 2" MCM Model 118 mud pump 350 gpm/95 psi, 150 rpm main drill head 1000 ft/lb torque, 55 gal hyd reservoir, 12,000# push/pull force w/chain hoist drive, 16'6" tubular 4x6 mast 12' stroke, designed for 10' Mayhew Jr drill pipe, 82000 BTU hydraulic oil cooler, swivel with extreme duty 18,000# twin thrust bearing set and shevron seals w/changeable ware sleeves, hydraulicuniversal breakout system, swing away drill head, ½" minimum watercourse through all piping, 22 gallon fuel tank, 20' of 3" charge line, 20' of 2" bypass hose w/cam locks, 12 volt primer and wash down pump, removable drill pipe guide, 1200# hydraulic accessory host telewscoping to 22' height for casing work w/drill pipe tool for lifting and handling drill stem. Weight (skid mounted unit): 6500 lbs., dimensions (trailer mounted) 110" long x 90" wide (will fit in 20' shipping container) Price, skid mounted: $59,500 Price, trailer mounted: $69,500

For Additional Information, Call, Email or Fax Maryann